Category : Shower Head

Shower Diverter Not Working? Its Solution Finally Here

A shower diverter is a device that diverts the shower from the bathtub faucet and vice versa, it is an important part of shower parts, However, over time, this shower diverter can corrode.

The tub faucet is failing to completely turn off the water due to corrosion, and the shower may not flow at all. If it does, the flow will be limited.

We often lack knowledge about shower heads, which is why we struggle to solve the problem of shower head flow restrictors.

In this blog, we will discuss how to fix the flow restrictor in your showerhead. We’ll also cover the types of flow restrictors that can benefit your future showers. Without further ado, let’s get started.

What Is a Shower Diverter?

A shower diverter is a valve that directs water between the showerhead and tub spout. It allows water to flow from the showerhead when turned on and from the tub faucet when closed.

Some diverters also have a built-in pressure-balancing feature that helps maintain a consistent water flow rate even when water pressure fluctuates.

What Type Of Shower Diverter Do You Have?

Shower diverters are an essential component of any shower and there are a few different types to choose from.

Golden Brass Finish Tee Valve and Written Over “1. Single or Tee Shower Diverter” Golden Brass Finish Two Valve and Written Over “2.Two Valve Shower Diverter” Golden Brass Finish Three Valve and Written Over “1. Three Valve Shower Diverter” and logo ””
Type Of Shower Diverter

Single Valve or Tee-Diverter:

Tee diverter, which has two handles that independently control the flow of water. The T diverter is often used in showers that each has separate shower heads and controls.

Two Valve Diverter:

A two valve diverter, also known as a shower diverter, is a plumbing fitting that controls the flow of water between two different pipes. Typically, one pipe supplies water to a shower, while the other pipe supplies water to a faucet or other fixture.

Three Valve Diverter:

Three way diverter, which allows you to control the flow of water to three different outlets. Three way diverters are often used in multi-head showers or when it is necessary to independently control the flow of water to multiple outlets.

How to Determine that Your Shower Diverter is Broken

If you suspect that your diverter is broken, there are a few signs to look for.

  • Water no longer flows from the showerhead when you turn on the shower.
  • Water is only coming out of the showerhead.
  • It is taking an unusually long time for hot water to reach the shower.

These indications suggest that your diverter is not functioning properly and requires repair or replacement.

How to Repair a Shower Diverter

a men wear a blue T-shirt  trying to shower diverter and written beside  "How to Repair a Shower Diverter" with logo ""

Step 1:Turn Off The Water

To repair your shower diverter, the first step is to turn off the water. This will prevent any further damage to the diverter while you work on it.

Step 2:Seal Off The Drain.

The second step is to seal off the shower drain. This is to prevent water from damaging the diverter while you work on it.

You can use a variety of materials to seal the drain, but duct tape is usually the easiest and most effective option. Make sure the tape is firmly attached to the drain so that no water escapes.

Step 3:Loosen The Waterspout’s Set Screw & Remove Waterspout

To repair your shower diverter, the third step is to unscrew the nut at the stem on the waterspout. This will allow you to remove the waterspout and access the shower diverter valve.

Step 4:Remove Diverter 

If you notice that the diverter is broken after loosening it, or that the rubber washer has worn out over time, you may need to replace the entire shower diverter or simply tighten the screws. Taking the necessary steps becomes very simple and less problematic.

Step 5:Replace Waterspout And Test

After making the necessary changes, immediately check if everything is working as before. Additionally, it is crucial to check for any leaks in the bathtub, as this is an urgent step.

Prevent Shower Diverter Wear and Tear:

Shower diverters can be subject to a lot of wear and tear over time. One way to help prevent shower diverter wear and tear is to clean the diverter regularly but avoid using harsh chemicals or abrasive cleaners on the diverter, as these can damage the finish.

This will help to remove any build-up of soap scum or other debris that can cause the diverter to stick or refuse to turn. In addition, it is important to check the diverter for signs of damage on a regular basis. If the diverter is cracked or otherwise damaged, it should be replaced as soon as possible.

Summary of Shower Diverter Not Working? Its Solution Finally Here

Shower diverters are a common household item in the bathroom that often needs fixing. Here we will show you how to fix your shower diverter step by step, to get it working properly again.

By following these simple instructions, you can save yourself time and money repairing your shower diverter.

If you have any questions or comments about bathroom accessories, please leave a comment, and we will respond.

If you want to interested in bathroom shower, bathtub, toilet ,bathroom floor and bathroom accessories please click our dedicated article on this website

FAQ: Shower Diverter Not Working? Its Solution Finally Here

Q1.How Much Does It Cost To Replace a Shower Diverter?

The cost of replacing a shower diverter depends on the type of shower head. For older models with one valve, labor costs around $30-$50 and parts cost $15-$20. For models with two valves, an extra valve is needed, making the replacement more expensive.

Q2. How Long Does a Shower Diverter Last?

Shower diverters can last for years if installed and maintained properly. However, the frequency of use and level of care can affect their lifespan. Some may need to replace the shower diverter every few months.

Q3.Are Shower Diverters Universal?

Shower diverters can have universal replacement parts available, but it is important to ensure that the replacement part will fit your specific shower system. Many manufacturers now have their own lines of shower products and often use their own types of fittings for valve connections.

1 thought on “Shower Diverter Not Working? Its Solution Finally Here”

Leave a Comment